adding in code
This commit is contained in:
talksik
@@ -0,0 +1,179 @@
|
||||
/* USER CODE BEGIN Header */
|
||||
/**
|
||||
******************************************************************************
|
||||
* @file : main.c
|
||||
* @brief : Main program body
|
||||
******************************************************************************
|
||||
* @attention
|
||||
*
|
||||
* <h2><center>© Copyright (c) 2019 STMicroelectronics.
|
||||
* All rights reserved.</center></h2>
|
||||
*
|
||||
* This software component is licensed by ST under BSD 3-Clause license,
|
||||
* the "License"; You may not use this file except in compliance with the
|
||||
* License. You may obtain a copy of the License at:
|
||||
* opensource.org/licenses/BSD-3-Clause
|
||||
*
|
||||
******************************************************************************
|
||||
*/
|
||||
/* USER CODE END Header */
|
||||
/* Interface definition
|
||||
SCL = PB8
|
||||
SDA = PB9
|
||||
*/
|
||||
/* Includes ------------------------------------------------------------------*/
|
||||
#include "main.h"
|
||||
#include "i2c.h"
|
||||
#include "usart.h"
|
||||
#include "gpio.h"
|
||||
#include "DEV_Config.h"
|
||||
#include "PAJ7620U2.h"
|
||||
unsigned char PAJ7620U2_init()
|
||||
{
|
||||
unsigned char i,State;
|
||||
DEV_Set_I2CAddress(PAJ7620U2_I2C_ADDRESS);
|
||||
DEV_Delay_ms(5);
|
||||
State = DEV_I2C_ReadByte(0x00); //Read State
|
||||
if (State != 0x20)
|
||||
return 0; //Wake up failed
|
||||
DEV_I2C_WriteByte(PAJ_BANK_SELECT, 0); //Select Bank 0
|
||||
for (i=0;i< Init_Array;i++)
|
||||
{
|
||||
DEV_I2C_WriteByte(Init_Register_Array[i][0], Init_Register_Array[i][1]);//Power up initialize
|
||||
}
|
||||
return 1;
|
||||
}
|
||||
void SystemClock_Config(void);
|
||||
/* USER CODE BEGIN PFP */
|
||||
|
||||
/* USER CODE END PFP */
|
||||
|
||||
/* Private user code ---------------------------------------------------------*/
|
||||
/* USER CODE BEGIN 0 */
|
||||
|
||||
/* USER CODE END 0 */
|
||||
|
||||
/**
|
||||
* @brief The application entry point.
|
||||
* @retval int
|
||||
*/
|
||||
int main(void)
|
||||
{
|
||||
/* USER CODE BEGIN 1 */
|
||||
|
||||
/* USER CODE END 1 */
|
||||
unsigned char i, OBJ_BRIGHTNESS;
|
||||
unsigned short OBJ_SIZE;
|
||||
|
||||
/* MCU Configuration--------------------------------------------------------*/
|
||||
|
||||
/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
|
||||
HAL_Init();
|
||||
|
||||
/* USER CODE BEGIN Init */
|
||||
|
||||
/* USER CODE END Init */
|
||||
|
||||
/* Configure the system clock */
|
||||
SystemClock_Config();
|
||||
|
||||
/* USER CODE BEGIN SysInit */
|
||||
|
||||
/* USER CODE END SysInit */
|
||||
|
||||
/* Initialize all configured peripherals */
|
||||
MX_GPIO_Init();
|
||||
MX_USART2_UART_Init();
|
||||
MX_I2C1_Init();
|
||||
printf("Gesture Sensor Test Program ...\r\n");
|
||||
if(!PAJ7620U2_init())
|
||||
{ printf("\nGesture Sensor Error\r\n");
|
||||
return 0;
|
||||
}
|
||||
printf("\nGesture Sensor OK\r\n");
|
||||
DEV_I2C_WriteByte(PAJ_BANK_SELECT, 0); //Select Bank 0
|
||||
for (i = 0; i <PS_Array_SIZE; i++)
|
||||
{
|
||||
DEV_I2C_WriteByte(Init_PS_Array[i][0], Init_PS_Array[i][1]);//Gesture register initializes
|
||||
}
|
||||
DEV_I2C_WriteByte(PAJ_BANK_SELECT, 0); //Select Bank 0
|
||||
while (1)
|
||||
{
|
||||
OBJ_BRIGHTNESS = DEV_I2C_ReadByte(PAJ_OBJ_BRIGHTNESS); //Read Data
|
||||
OBJ_SIZE = DEV_I2C_ReadWord(PAJ_OBJ_SIZE_L);
|
||||
printf("Object brightness = %d ,Object size = %d\r\n", OBJ_BRIGHTNESS, OBJ_SIZE);//Object Brightness (Max. 255),Object Size (Max. 900)
|
||||
DEV_Delay_ms(300);
|
||||
}
|
||||
}
|
||||
|
||||
/**
|
||||
* @brief System Clock Configuration
|
||||
* @retval None
|
||||
*/
|
||||
void SystemClock_Config(void)
|
||||
{
|
||||
RCC_OscInitTypeDef RCC_OscInitStruct = {0};
|
||||
RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
|
||||
|
||||
/** Initializes the CPU, AHB and APB busses clocks
|
||||
*/
|
||||
RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
|
||||
RCC_OscInitStruct.HSEState = RCC_HSE_ON;
|
||||
RCC_OscInitStruct.HSEPredivValue = RCC_HSE_PREDIV_DIV1;
|
||||
RCC_OscInitStruct.HSIState = RCC_HSI_ON;
|
||||
RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
|
||||
RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
|
||||
RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL9;
|
||||
if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
|
||||
{
|
||||
Error_Handler();
|
||||
}
|
||||
/** Initializes the CPU, AHB and APB busses clocks
|
||||
*/
|
||||
RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
|
||||
|RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
|
||||
RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
|
||||
RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
|
||||
RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
|
||||
RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
|
||||
|
||||
if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK)
|
||||
{
|
||||
Error_Handler();
|
||||
}
|
||||
}
|
||||
|
||||
/* USER CODE BEGIN 4 */
|
||||
|
||||
/* USER CODE END 4 */
|
||||
|
||||
/**
|
||||
* @brief This function is executed in case of error occurrence.
|
||||
* @retval None
|
||||
*/
|
||||
void Error_Handler(void)
|
||||
{
|
||||
/* USER CODE BEGIN Error_Handler_Debug */
|
||||
/* User can add his own implementation to report the HAL error return state */
|
||||
|
||||
/* USER CODE END Error_Handler_Debug */
|
||||
}
|
||||
|
||||
#ifdef USE_FULL_ASSERT
|
||||
/**
|
||||
* @brief Reports the name of the source file and the source line number
|
||||
* where the assert_param error has occurred.
|
||||
* @param file: pointer to the source file name
|
||||
* @param line: assert_param error line source number
|
||||
* @retval None
|
||||
*/
|
||||
void assert_failed(uint8_t *file, uint32_t line)
|
||||
{
|
||||
/* USER CODE BEGIN 6 */
|
||||
/* User can add his own implementation to report the file name and line number,
|
||||
tex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
|
||||
/* USER CODE END 6 */
|
||||
}
|
||||
#endif /* USE_FULL_ASSERT */
|
||||
|
||||
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|
||||
Reference in New Issue
Block a user